Fundamentos E Engenharia
Pump Construction (Part1)
In 1689 the physicist Denis Papin invented the centrifugal pump and today this kind of pump is the most used around the world. The centrifugal pump is built on a simple principle: Liquid is led to the impeller hub and by means of the centrifugal force it is flung towards the periphery of the impellers. The construction is fairly inexpensive, robust and simple and its high speed makes it possible to connect the pump directly to an asynchronous motor.
Expansion Valves Selection
The expansion valve regulates the amount of compressed liquid refrigerant moving into the evaporator. It removes pressure from the liquid refrigerant to allow expansion or change of state from a liquid to a gas in the evaporator. In order to properly select Expansion Valves one should pay attention to the items that we mention in this post.
Water Tube Versus Fire Tube Boilers
Water tube boilers and fire tube boilers are two different types of steam boilers that are commonly used in industrial and commercial applications. Both types of boilers use a system of tubes to generate steam, but they differ in the way that the tubes are arranged and the way that the hot gases from the burner pass through the tubes.
Water Hammer (Part1)
Under unfavorable circumstances, damage due to water hammer may occur in pipelines measuring more than one hundred meters and conveying only several tenths of a liter per second. But even very short, unsupported pipelines in pumping stations can be damaged by resonant vibrations if they are not properly anchored. By contrast, the phenomenon is not very common in building services systems, e.g. in heating and drinking water supply pipelines, which typically are short in length and have a small cross-section.
Refrigeration Formulas and Calculations
These formulas are commonly used in the field of refrigeration and air conditioning to calculate various performance parameters of a refrigeration system such as compression work, compression power, coefficient of performance, net refrigeration effect, capacity, compressor displacement, heat of compression, volumetric efficiency, and compression ratio. These formulas are based on the thermodynamics principles and are generally used to evaluate the performance of the refrigeration system and to optimize its design.
The coefficient of velocity (Cv)
Cv, or coefficient of velocity, is a measure of the flow capacity of a valve. It represents the number of gallons per minute (GPM) of water at 60°F that will flow through a valve with a one-inch opening at a pressure drop of one pound per square inch (PSI). Cv can be calculated using various formulas, such as the one based on water at 60F and one that takes into account the specific gravity of the fluid. Cv is a theoretical value and it may vary depending on the actual conditions of the valve. When selecting a valve for a specific application, it is important to consider the Cv in relation to the flow rate and pressure drop requirements of the system, as well as other factors such as ease of maintenance, cost, and safety.
Pipe Insulation Guideline
Pipe insulation is crucial for maintaining energy efficiency, temperature control, condensation control, noise reduction, and safety. ASHRAE provides specific thickness recommendations for different pipe sizes and temperature ranges in its standard 90.1. When selecting pipe insulation based on ASHRAE standards, it’s important to consider the temperature, pipe size, environmental considerations, fire resistance, and energy efficiency.
Refrigerant Piping – part2
In this post, we will be continuing our comprehensive training on how to size refrigerant piping. We will cover all the important aspects of this process, including determining the pipe size, pressure drop, and other factors. We will also discuss topics such as sizing refrigerant lines, equivalent length for refrigerant lines, and how to determine equivalent length. With this training, you will have the knowledge and confidence to size refrigerant piping accurately and correctly in any situation.
Padrões E Conformidade
Projeto de ventilação HVAC: Ventilação de ar de exaustão por taxa e ACH
Complete guide to HVAC exhaust air ventilation design using ASHRAE, CIBSE, and Carrier standards covering rate calculations, ACH requirements, and specialized applications for effective contaminant removal and energy efficiency.
Projeto de ventilação HVAC: Ventilação de ar externo por taxa e ACH
Complete guide to HVAC outdoor air ventilation design using ASHRAE, CIBSE, and Carrier standards covering rate calculations, ACH requirements, and building-specific applications for optimal indoor air quality.
Projeto de ventilação HVAC: qualidade do ar interno e contaminantes do ar
Complete guide to HVAC indoor air quality and air contaminant management using ASHRAE, CIBSE standards covering contaminant identification, control strategies, and advanced treatment technologies for healthy indoor environments.
HVAC Ventilation Design: Air Intake Minimum Separation Distance
Complete guide to HVAC air intake minimum separation distances using ASHRAE 62.1 standards covering contamination source requirements, measurement methods, and compliance strategies for optimal outdoor air quality protection.
HVAC Ventilation Design: Air Classifications
Complete guide to HVAC air classifications using ASHRAE 62.1 and CIBSE standards covering air quality categories, contamination levels, filtration requirements, and ventilation strategies for optimal indoor environmental control.
HVAC Ventilation Design: General Schematic and Equations
Complete guide to HVAC ventilation design using ASHRAE 62.1 standards covering calculation procedures, system schematics, and modern ventilation strategies for optimal indoor air quality and energy efficiency.
Estimativa de carga HVAC: fator de incrustação
Complete guide to fouling factors in HVAC load estimation using Carrier water conditioning standards for accurate heat transfer equipment sizing and comprehensive water quality management strategies.
HVAC Load Estimation: Diversity Factor
Complete guide to diversity factors in HVAC load estimation using CIBSE and Carrier standards for accurate system sizing that reflects realistic building operation patterns and prevents equipment oversizing.
Estimativa de carga HVAC: condições de projeto interno e requisitos do sistema por tipo de edifício
Complete guide to indoor design conditions for HVAC load estimation covering temperature, humidity, air quality, and specialized requirements for residential, commercial, industrial, healthcare, and specialty building applications using ASHRAE, CIBSE, and Carrier standards.
Estimativa de carga HVAC: ganho e perda de calor por infiltração
Complete guide to infiltration in HVAC load estimation using ASHRAE, CIBSE, and Carrier standards for accurate assessment of uncontrolled air exchange and its impact on heating and cooling loads.
Ferramentas E Recursos Digitais
Psychrometric Programming Functions
ibrary of psychrometric functions to calculate thermodynamic properties of air for Python, C, C#, Fortran, JavaScript and VBA/Excel
Software Carrier Hap
Carrier’s Hourly Analysis Program is two powerful tools in one package – versatile features for designing HVAC systems for commercial buildings AND powerful energy analysis capabilities for comparing energy consumption and operating costs of design alternatives.
Trace 700 Software
TRACE 700 enables building designers to optimize the building, system and equipment designs on the basis of energy utilization and life-cycle cost. The Trane software for TRACE 700 facilitates analysis of the energy and economic effects of virtually any chiller plant configuration by allowing users to manipulate a wide range of variables and create a profile of their specific building.
Baixe EVAP-COND 5.0: A ferramenta definitiva de simulação de trocador de calor para engenheiros de HVAC
Whether you’re designing a new heat exchanger, optimizing an existing system, or researching alternative refrigerants, EVAP-COND provides the detailed analysis capabilities needed to make informed decisions. I encourage all HVAC engineers and researchers to explore this powerful simulation tool and experience firsthand how it can transform your approach to heat exchanger design.
Heat Transfer Textbook Download
The book is meant for juniors, seniors, and first-year graduate students. And to those who choose to learn the subject on their own, and to practicing engineers who use it as a reference. Whether one studies alone or with a class, learning means posing, then answering, one’s own questions.